Determining optimal length of coracoid graft in the modified Bristow procedure for anterior shoulder instability: A three-dimensional finite element analysis.

BACKGROUND: There is a lack of consensus concerning the coracoid graft length in the modified Bristow procedure. OBJECTIVE: We attempted to determine the optimal graft length using the three-dimensional finite element method. METHODS: In a shoulder model with a 25% anterior glenoid defect, a coracoid graft of varying lengths (5, 10, 15, and 20 mm) was fixed using a half-threaded screw. First, a compressive load of 500 N was applied to the screw head to determine the graft failure load during screw tightening. Next, a tensile load (200 N) was applied to the graft to determine the failure load due to biceps muscle traction. RESULTS: In the screw compression, the failure loads in the 5-, 10-, 15-, and 20-mm models were 252, 370, 377, and 331 N, respectively. In the tensile load applied to the coracoid graft, the failure load exceeded 200 N for both the 5- and 10-mm models. CONCLUSION: The 5-mm graft had a high risk of fracture during intraoperative screw tightening. As for the biceps muscle traction, the 5- and 10-mm-grafts had a lower failure risk than the 15- and 20-mm-grafts. Therefore, we believe that the optimal length of the coracoid graft is 10 mm in the modified Bristow procedure.

Intra-articular biomechanical environment following modified Bristow and Latarjet procedures in shoulders with large glenoid defects: relationship with postoperative complications.

BACKGROUND: Although coracoid transfers including the modified Bristow and Latarjet procedures are widely used to treat anterior shoulder instability, the influence of the choice of procedure on the biomechanical outcomes is not well characterized. We aimed to clarify the intra-articular stress distribution following these 2 procedures using 3-dimensional finite-element analysis and to investigate the role of stress distribution in the pathophysiology of postoperative complications. METHODS: Overall, 6 male patients aged 17-47 years with unilateral anterior shoulder instability were recruited. Computed tomographic digital imaging and communications in medicine (CT-DICOM) data of the contralateral (healthy) shoulder of each patient was obtained and used for developing the 3-dimensional normal glenohumeral joint model. A 25% bony defect was created in the anterior glenoid rim where the coracoid process was transferred in the standing and lying-down positions to create the Bristow and Latarjet models, respectively. The arm position was set as 0° or 90° abduction. The Young moduli of the humerus and scapula were calculated using CT data, and set as 35.0 MPa and 113.8 GPa for the articular cartilage and inserted screw, respectively. A compressive load (50 N) was applied to the greater tuberosity toward the center of the glenoid, and a tensile load (20 N) was applied to the tip of the coracoid in the direction of conjoint tendon. Elastic analysis was used to determine the equivalent stress distribution. RESULTS: A significant reduction in mean equivalent stress was observed within the glenoid cartilage for both models (P = .031); however, a new stress concentration appeared within the grafted coracoid-facing region of the humeral-head cartilage in both models. The proximal half of the coracoid graft exhibited lower equivalent stress than the distal half in 5 of the 6 Latarjet models, whereas the proximal half showed higher equivalent stress than the distal half in all 6 Bristow models. High stress concentration was identified at the midpoint of the inserted screw in Bristow models. DISCUSSION AND CONCLUSIONS: Intra-articular stress distribution may explain the different rates of postoperative complications associated with the modified Bristow and Latarjet procedures. New stress concentration within the humeral-head cartilage might contribute to the development of glenohumeral osteoarthritis following both procedures. Stress shielding in the proximal part of the coracoid graft might contribute to osteolysis following the Latarjet procedure. Surgeons should be aware of the risk of breakage of the inserted screw following the modified Bristow procedure.

Comparison between single and double suture passing techniques in the suture bridge rotator cuff repair with a 2-mm tape: A simulation study using a three-dimensional finite element method.

BACKGROUND: Suture bridge repair has been widely used as one of the standard procedures in the arthroscopic rotator cuff repair. We compared the intratendinous stress distribution between single and double suture passing techniques in the suture bridge repair using a 2-mm tape and clarified the roles of tensioning in this procedure. METHODS: A board-like model of the supraspinatus tendon and humeral head was used in order to standardize conditions and exclude the influence of anatomical variations between individuals. Reattachment of the supraspinatus tendon to the bone was simulated using both single and double suture passing techniques for the suture bridge repair using a 2-mm tape. A tensile load was applied to the medial end of the tendon, and the stress distribution pattern was observed. Elastic analysis enabled comparison of the von Mises equivalent and maximum principal stresses between the single and double suture passing techniques. The tape configuration was subsequently translated 1 mm toward the insertion points of lateral anchors to simulate the tensioning maneuver. RESULTS: Although the distribution pattern of both the equivalent and the maximum principal stresses was similar for both models, areas with a high stress concentration were smaller in the single suture passing model than those in the double suture passing model. The equivalent stress concentrated within the tendon beneath the tapes as well as in the area between the crossing tapes and the lateral end of the tendon, whereas the maximum principal stress concentrated medial to the sites of suture penetration. CONCLUSIONS: Single suture passing technique can reduce the extent of intratendinous stress concentration compared with double suture passing technique, which might be beneficial to reduce the incidence of type 2 retear after suture bridge repair of rotator cuff tendon using a 2-mm tape.

Proximal-medial part in the coracoid graft demonstrates the most evident stress shielding following the Latarjet procedure: a simulation study using the 3-dimensional finite element method.

BACKGROUND: Although the osteolysis of the coracoid graft is frequently observed after the Latarjet procedure particularly in its proximal part, its pathomechanism is not well understood. METHODS: Three-dimensional finite element glenohumeral joint models were developed using CT-DICOM data of 10 normal shoulders. A 25% bony defect was created on the anterior glenoid rim, and the coracoid process was transferred flush with the glenoid cartilage using 2 half-threaded screws. In the hanging arm as well as in the 90° abducted positions, a compressive load (50 N) was applied to the greater tuberosity toward the center of the glenoid and a tensile force (20 N) was applied to the coracoid tip along the direction of the conjoint tendon. Next, elastic analysis was performed, and the distribution patterns of the equivalent stress as well as the maximum principal stress were compared among 4 parts (proximal/distal and medial/lateral) of the coracoid graft. RESULTS: Both the equivalent stress and the maximum principal stress were reduced in the proximal half of the coracoid graft. A high stress concentration was observed in the lateral aspect of the coracoid graft particularly in the 90° abducted position. The proximal-medial part demonstrated the lowest equivalent stress as well as the maximum principal stress for both arm positions, which were significantly lower than those in the distal 2 parts. CONCLUSION: In the Latarjet procedure, the proximal-medial part of the coracoid graft demonstrated the most evident stress shielding, which may play an important role in postoperative osteolysis.

Muscle activities during shoulder internal rotation differ in arm position: a preliminary quantitative analysis using positron emission tomography.

OBJECTIVE: To investigate the muscle activity patterns of the glenohumeral joint during internal rotation both with the arm at 0° and 90° of abduction using 2-deoxy-2-[18F] fluoro-D-glucose (FDG) positron emission tomography (PET) and magnetic resonance imaging (MRI). MATERIALS AND METHODS: Six healthy male volunteers underwent PET examination after performing active glenohumeral internal rotation exercise using an elastic band both with the arm at 0° and 90° of abduction. As a control, PET scan under resting condition was also performed. The exercise was performed before and after 18 fluorodeoxyglucose injection. Each PET image was fused to the corresponding MRI to identify each muscle. The standardized uptake value (SUV) of each muscle was compared between the two arm positions. RESULTS: With the arm at 0° of abduction, the SUV increased significantly after exercise both in the middle and inferior 1/3 of the subscapularis, which were significantly higher than that of the superior 1/3 of the subscapularis (P < 0.05). The SUV of the inferior 1/3 of the subscapularis was significantly higher at 90° of abduction than at 0° of abduction and was significantly higher than that of the superior 1/3 at 90° of abduction (P < 0.01). The SUV after exercise in the inferior infraspinatus and teres minor increased. CONCLUSIONS: The middle and inferior parts of the subscapularis are the main shoulder internal rotators in 0° of abduction, whereas the inferior part of the subscapularis is the main internal rotator in 90° of abduction.

Representative survey of frozen shoulder questionnaire responses from the Japan Shoulder Society: What are the appropriate diagnostic terms for primary idiopathic frozen shoulder, stiff shoulder or frozen shoulder?

BACKGROUND: Primary frozen shoulder has unknown etiology and significant restriction of active and passive motion. The distinction between frozen shoulder and stiff shoulder has been unclear. Therefore, the purposes of this study were to perform a survey regarding definition and classification of frozen shoulder proposed by the American Academy of Orthopedic Surgeons (AAOS) among the members of the Japan Shoulder Society (JSS) and to compare the results with those obtained among the members of the American Shoulder and Elbow Surgeons (ASES). METHODS: The Scientific Research Project Committee of the JSS prepared the questionnaire for frozen shoulder and stiff shoulder. Surveys were sent by e-mail on Jan 14, 2016 to JSS registered members and the response dead-line was set on March 13, 2016. RESULTS: The number of respondents was 230, including all directors, councilors, and senior doctors. Agreement with the definition of primary frozen shoulder was 67%, the classification of primary or secondary frozen shoulder was 53%, and the 3 divisions of secondary frozen shoulder was 53%. Diagnostic terms for the cases of shoulder stiffness with unknown etiology were as follows: frozen shoulder (31%), stiff shoulder (22%), periarthritis scapulohumeralis (16%), so called "Gojukata" in Japan, which means shoulder problems in their fifties (16%), idiopathic frozen shoulder (6%), primary frozen shoulder (4%), adhesive capsulitis (3%), others (2%). CONCLUSION: The survey shows lower rates of agreement among the JSS members than the ASES members for the definition of primary frozen shoulder, the classification of primary and secondary frozen shoulder, and the divisions of secondary frozen shoulder. To avoid confusion between stiff shoulder and frozen shoulder, the committee agrees to the ISAKOS recommendation that the term "frozen shoulder" should be used exclusively for primary idiopathic stiff shoulder.

Risk Factors for Tear Progression in Symptomatic Rotator Cuff Tears: A Prospective Study of 174 Shoulders.

BACKGROUND: The risk factors for tear progression in symptomatic rotator cuff tears have not been clarified yet. It is important for orthopaedic surgeons to know the natural course of tear progression when nonoperative management is to be chosen. HYPOTHESIS: Tears in younger patients, high-activity patients, or heavy laborers would progress in size more than those in older patients, low-activity patients, or light laborers. STUDY DESIGN: Case-control study; Level of evidence, 3. METHODS: Two hundred twenty-five consecutive patients with symptomatic rotator cuff tears visited our institute between 2009 and 2015. Of these, 174 shoulders of 171 patients (mean age, 66.9 years) who underwent at least 2 magnetic resonance imaging (MRI) examinations were prospectively enrolled. The mean follow-up was 19 months. Tear progression was defined as positive when the tear size increased by ≥2 mm. The demographic factors that were analyzed by multivariate analysis included age, sex, hand dominance, smoking, alcohol drinking, hypercholesterolemia, sports participation, job type, tear size, and tear type (full or partial thickness). RESULTS: Of the 174 shoulders, 82 shoulders (47%) showed tear progression. The mean (±SD) tear length and width in the progression group on final MRI were 23.1 ± 12.5 mm and 17.3 ± 9.6 mm, respectively; the tear size progressed by a mean 5.8 ± 5.6 mm in length and 3.1 ± 5.2 mm in width. The mean propagation speed was 3.8 mm/y in length and 2.0 mm/y in width. The size of full-thickness tears significantly increased compared with that of articular-sided partial-thickness tears ( P = .0215). The size of medium tears significantly increased compared with that of other tears ( P < .0001). According to the logistic regression analysis, smoking was significantly correlated with tear progression ( P = .026). Subgroup analyses showed that male sex, hand dominance, and trauma were correlated with tear progression. Age, alcohol drinking, hypercholesterolemia, sports participation, and job type did not show any correlation with tear progression. CONCLUSION: The tear size of symptomatic rotator cuff tears progressed in 47% of the shoulders during a mean of 19 months, and the speed of progression was 3.8 mm/y in length and 2.0 mm/y in width. The risk factors for tear progression were (1) a medium-sized tear, (2) a full-thickness tear, and (3) smoking.

Tight medial knot tying may increase retearing risk after transosseous equivalent repair of rotator cuff tendon.

BACKGROUND: Retearing mechanism after transosseous equivalent (TOE) rotator cuff repair has not been fully clarified yet. OBJECTIVE: The purposes of this study were to compare the stress distribution pattern in the tendon stump between knotted and knotless TOE repair and to investigate the role of suture tension applied during medial knot tying using a 3-dimensional finite element (3D-FE) method. METHODS: Both knotted and knotless TOE repairs were simulated on the 3D-FE human rotator cuff tear model. Elastic analysis was performed to compare the stress distribution pattern inside the tendon between the two models. The amount of compressive load applied to the medial-row sutures was then changed as 0, 20, 40, 60, 80, and 100 N in the knotted model. RESULTS: Knotted model demonstrated more distinct stress concentration inside the tendon around medial-row sutures than the knotless model. Mean von Mises equivalent stress in this area in the 0, 20, 40, 60, 80, and 100 N models was 0.26, 0.35, 0.50, 0.70, 1.11, and 1.14 MPa, respectively. CONCLUSIONS: In the knotted TOE repair, tight medial knot tying might cause a high stress concentration around medial knots, which may constitute one of the pathogenetic factors of postoperative retearing at this site.

Three-Dimensional Morphometric Analysis of the Coracohumeral Distance Using Magnetic Resonance Imaging.

There have been no studies investigating three-dimensional (3D) alteration of the coracohumeral distance (CHD) associated with shoulder motion. The aim of this study was to investigate the change of 3D-CHD with the arm in flexion/internal rotation and horizontal adduction. Six intact shoulders of four healthy volunteers were obtained for this study. MRI was taken in four arm positions: with the arm in internal rotation at 0°, 45°, and 90° of flexion, and 90° of flexion with maximum horizontal adduction. Using a motion analysis system, 3D models of the coracoid process and proximal humerus were created from MRI data. The CHD among the four positions were compared, and the closest part of coracoid process to the proximal humerus was also assessed. 3D-CHD significantly decreased with the arm in 90° of flexion and in 90° of flexion with horizontal adduction comparing with that in 0° flexion (P<0.05). In all subjects, lateral part of the coracoid process was the closest to the proximal humerus in these positions. In vivo quasi-static motion analysis revealed that the 3D-CHD was narrower in the arm position of flexion with horizontal abduction than that in 0° flexion. The lateral part on the coracoid process should be considered to be closest to the proximal humerus during the motion.

A biomechanical study on suture anchor insertion angle: Which is better, 90° or 45°?

INTRODUCTION: The purpose of this study was to compare the pullout strength of anchors inserted at 90° and 45° to the bone surface using synthetic bones and porcine humeri. SUBJECTS AND METHODS: Pullout tests were performed by universal testing machine. Synthetic cancellous bones of 0.08, 0.16, and 0.24 g/cm3 (defining as low, medium and high density, respectively) with 2-mm-thick cortical bone model attached on one side and the greater tuberosity of porcine humeri (average bone density, 270 mg/cm3) were chosen for pullout tests. Metallic anchors were inserted at 90° or 45° to the surface and pulled at 90° or 45° from the surface. The maximum load to failure for each condition was recorded. Differences in pullout failure loads between insertion angle, pulling angle, and bone density were analyzed. RESULTS: When the sutures were pulled at 90° in low, medium, high density bones, and porcine humeri, 90°-inserted-anchors showed higher pullout strength than the 45°-inserted-anchors (534.6 ± 28.9 N vs. 488.1 ± 25.3 N (p < 0.05), 636.8 ± 25.3 N vs. 517.5 ± 27.4 N (p < 0.01), 735.6 ± 45.1 N vs. 557.0 ± 42.5 N (p < 0.01), and 285.6 ± 47.2 N vs. 181.4 ± 31.3 N (p < 0.01), respectively). When the sutures were pulled at 45° in low, medium density bones and porcine humeri, 90°-inserted-anchors showed higher pullout strength than the 45°-inserted-anchors (651.1 ± 38.3 N vs. 529.4 ± 37.6 N (p < 0.01), 711.4 ± 25.3 N vs. 599.2 ± 29.8 N (p < 0.01), and 265.3 ± 49.0 N vs. 181.5 ± 29.4 N (p < 0.01), respectively). CONCLUSION: Pullout strength of the anchors inserted at 90° to the bone surface was greater than the anchors inserted at 45° regardless of the bone density.

Comfort and acceptability of various immobilization positions using a shoulder external rotation and abduction brace.

BACKGROUND: Immobilization with shoulder braces is used for conservative treatment of an initial shoulder dislocation. Various arm positions have been investigated to determine optimal position in terms of the anatomical reduction of the Bankart lesion. Recently, the effect of immobilization in shoulder abduction as well as in external rotation has been reported. However, there are few studies assessing subjects' acceptability of the brace in various arm positions. We hypothesized that a certain arm position regarding abduction or external rotation for immobilization would induce significant discomfort during activities of daily living. METHODS: A dominant arm of 20 healthy participants was immobilized with a shoulder brace in 4 different positions; adduction and internal rotation (Add-IR), adduction and external rotation (Add-ER), 30° of abduction and 30° of external rotation (Abd-30ER), and 30° of abduction and 60° of external rotation (Abd-60ER). After completing immobilization for 24 h, subjects were asked to assess the discomfort of bracing for overall and individual activities, using a visual analogue scale. Data were compared among the four positions. RESULTS: For overall activities and several activities (eating, reading books, and removing and putting on pants), Abd-60ER was significantly more uncomfortable than adducted arm positions. Abd-30ER did not show any differences compared to the other arm positions. CONCLUSION: Immobilization in abduction and external rotation seems to be acceptable although the arm position in 30° of abduction and 60° of external rotation is less comfortable than the others. Our results might be useful in determining and developing the ideal shoulder brace which could keep patients' compliance and improve their outcomes.

Deadman theory revisited12.

The deadman theory is composed of two angles: θ1 and θ2, and it is recommended that both be less than or equal to 45°. Based on this theory, surgeons insert the anchor at 45°. However, the biomechanical studies show controversial data. We reviewed the original article and the biomechanical studies in the literature. We further performed three additional studies: 1) a finite element analysis to calculate the pullout strength of thread-less anchors inserted at 45°, 90°, and 135° to the polyurethane foam; 2) the same pullout test using thread-less anchors and the polyurethane foam; and 3) the same pullout test using metal threaded suture anchors and the simulated cortical bone. From the review and the additional studies, we came to the following explanations for the controversy: #1, the trigonometric calculation is not always applicable because of bone deformation; #2, insertion angle of 45° is the best for a thread-less anchor, but not for a threaded anchor; #3, θ1⩽45° is true, but it is not equivalent to inserting an anchor at 45°. In conclusion, insertion angle of 45° is the strongest for a thread-less anchor, but 90° is the strongest for a threaded anchor. The pullout strength depends on the inclination of the anchor, friction of the anchor-bone interface, and quality of the bone.

Comparison of fixation properties between coil-type and screw-type anchors for rotator cuff repair: A virtual pullout testing using 3-dimensional finite element method.

BACKGROUND: Pullout of inserted anchor constitutes one of the pathomechanisms of re-tearing after rotator cuff repair. The purpose of the present study was to investigate the fixation properties of suture anchors using 3-dimensional finite element method. METHODS: The computer models of three types of anchors (TwinFix Ti, HEALICOIL PK and HEALICOIL RG) were inserted into the isotropic cube model that simulated cancellous bone. In the virtual pullout testing, a tensile load (500 N) along the long axis of the inserted anchor was applied to the site of suture thread attachment to simulate a traction force. The distribution of von Mises equivalent stress, the failure patterns of elements inside the cube and the anchor displacement were compared among the three anchors. RESULTS: In TwinFix Ti, the highest stress concentration was seen around the anchor threads close to the surface of the cube, which caused element failure at this site. On the other hand, both HEALICOIL PK and HEALICOIL RG demonstrated a high stress concentration as well as element failure around the anchor tip. Comparing the anchor displacement, HEALICOIL RG showed the smallest displacement among the three anchors. The tensile loads that required a 0.1-mm displacement for TwinFix Ti, HEALICOIL PK and HEALICOIL RG were 400 N, 370 N, and greater than 500 N, respectively. CONCLUSIONS: The bony structures close to the footprint surface may be damaged during surgery due to preparation for the bony bed as well as the insertion of anchors. Thus, we assumed that HEALICOIL RG represented the best initial fixation properties among the three anchors tested. Virtual pullout testing using 3-dimensional finite element method could reveal the detailed biomechanical characteristics of each suture anchor, which would be important for shoulder surgeons to improve the clinical outcomes of rotator cuff repair.

Prediction of pathological fracture of the femoral shaft with an osteolytic lesion using a computed tomography-based nonlinear three-dimensional finite element method.

BACKGROUND: Physicians radiologically estimate the reduction in bone strength based on the size or location of bone tumors. The goal of this study was to clarify the relationship between the size or location of a bony defect and its mechanical strength using a computed tomography-based three-dimensional finite element method. METHODS: Computed tomography data of the right femur from two volunteers (one healthy male and one female patient with primary osteoporosis) were used for the present study. A spherical defect of various sizes and locations at the level of the isthmus of the femoral shaft was created on the three-dimensional finite element models to simulate the osteolytic bone tumor. We classified these defects into three types: inner erosion, cortical disruption, and outer erosion. Two types of mechanical testing were performed: axial compression and torsion. RESULTS: In the axial compression testing of the healthy male subject, the correlation coefficients between the defect rate and the failure load in the cortical disruption type, inner erosion type, and outer erosion type were -0.916, -0.358, and -0.106, respectively. In the torsion testing, they were -0.8744, -0.9001, and -0.8907, respectively. In the axial compression testing of the osteoporotic female subject, the correlation coefficients in the cortical disruption type, inner erosion type, and outer erosion type were -0.754, -0.621, and -0.158, respectively. In the torsion testing, they were -0.9199, -0.5098, and -0.8363, respectively. In both tests, the defect rate of the cortex increased and the bone strength decreased, especially in the cortical disruption type. CONCLUSION: The results of the present study demonstrate that osteolytic bone tumors can weaken the bone strength, particularly when perforation of the cortex occurs via tumor invasion. These results may be useful for risk assessment of pathological fractures due to primary and metastatic osteolytic bone tumors in clinical practice.

Patient trends in orthopedic traumas and related disorders after tsunami caused by the Great East Japan Earthquake: An experience in the primary referral medical center.

BACKGROUND: In the Great East Japan Earthquake, the Japanese Red Cross Ishinomaki Hospital played an important role as a principal referral center within the Ishinomaki region, one of the most severely affected areas in eastern Japan. The present study describes the patient population, clinical characteristics, and time courses of the medical problems observed at this hospital. METHODS: A retrospective survey of medical logs and records was conducted on the first 2 weeks after the earthquake to characterize orthopedic traumas and related disorders treated during this catastrophe. Patient number, severity of injuries, number of patients secondarily transported to the referral medical centers in the inland area, and the number of surgeries performed during the study period were investigated. RESULTS: Totally, 7686 patients visited the hospital. Of which, 1807 patients suffered from exogenous diseases, such as trauma, burns, crush syndrome, deep venous thrombosis, and infectious diseases. Patients who suffered from hypothermia were the most frequently seen within the first 2 weeks after the earthquake. Interestingly, most patients' conditions were not severe and required only simple treatments. Four patients (0.2% of patients with exogenous diseases) were secondarily transported to the referral medical centers in the inland area and only four patients were surgically treated because of a lack of available implants, surgical devices, and electric power supply. DISCUSSION AND CONCLUSIONS: The Great East Japan Earthquake and subsequent tsunami, which occurred during an early spring afternoon, resulted in a unique orthopedic patient population, which included few severely injured patients compared with numerous deaths. We believe that each coastal region hospital should develop its own emergency medical care system to address future tsunami events while considering their surrounding environment. The information described in the present study should be important for preparation toward future events involving massive earthquakes followed by tsunami disasters.

Association between acromioclavicular joint pain and capsular bulging in adolescent baseball players.

PURPOSE: The purpose of this study was to investigate the association between acromioclavicular (AC) joint pain and superior capsular bulging assessed by ultrasound in adolescent baseball players. METHODS: One hundred and fifty players (1st-8th graders) were examined. All subjects underwent physical examinations, including assessment of tenderness on the AC joint and provocative tests (the Buchberger's test and the cross-body adduction stress test). Bilateral AC joints with the arm in both the resting and the cross-body positions were examined by ultrasound. RESULTS: Twelve of 150 players (8 %) had AC symptoms with both positive tenderness and positive provocative tests. Interestingly, their prevalence increased with age-one of the 70 (1.4 %) 1st-3rd graders, six of 46 (13 %) 4th-6th graders and five of 34 (15 %) 7th-8th graders. Ultrasonography of AC joints in the cross-body position showed that the difference in superior capsular bulging between the throwing and non-throwing sides was significantly greater in symptomatic players (1.6 ± 1.2 mm) than in asymptomatic players (0.2 ± 0.8 mm) (p = 0.002). CONCLUSION: The prevalence of superior capsular bulging was significantly higher in adolescent baseball players with AC joint pain than in those without it. In adolescent baseball players with shoulder pain, AC joint symptoms should be considered amongst potential causes. Careful observation of these patients is suggested in cases of superior capsular bulging of the AC joint as determined by ultrasonography. LEVEL OF EVIDENCE: III.

Evaluation of the thickness of the medial ulnar collateral ligament in junior high and high school baseball players.

BACKGROUND: Thickening of the medial ulnar collateral ligament in the throwing arm of adult baseball players is a well-known phenomenon. However, onset of the thickening is unclear among young baseball players. The purpose of this study was to evaluate the thickness of the medial ulnar collateral ligament in junior high and high school baseball players. SUBJECTS AND METHODS: Seventy-one uninjured and asymptomatic junior high and high school baseball players were included in the study. Participants underwent physical examination after completing a questionnaire, followed by ultrasonographic evaluation. The thickness of the medial ulnar collateral ligament was measured bilaterally. The thickness of the throwing and non-throwing sides in high school and junior high school baseball players, and within each group, was compared and statistically analyzed. RESULTS: The medial ulnar collateral ligament in the throwing arm of high school baseball players was thicker than that in the non-throwing arm (5.5 vs. 4.4 mm), although no significant difference was seen in junior high school baseball players. High school baseball players showed a significantly thicker medial ulnar collateral ligament in the throwing arm than junior high school baseball players. CONCLUSION: Thickening of the medial ulnar collateral ligament in the throwing arm of asymptomatic and uninjured baseball players may begin by the time the players reach high school.

Predicting failures of suture anchors used for rotator cuff repair: a CT-based 3-dimensional finite element analysis.

BACKGROUND: Failure of inserted anchors has been recognized as one of the major pathomechanisms of re-tearing after rotator cuff repair. OBJECTIVE: To predict the inserted anchor failure using CT-based 3-dimensional finite element method (CT/3D-FEM). METHODS: Among twenty patients who underwent rotator cuff repair, 5 had anchor failure (failed anchor group) and 15 had no anchor failure (stable anchor group). A 3D model of proximal humerus was developed for each patient based on the CT data. A virtual pullout testing of TWINFIX™ anchors inserted into bone at 6 different sites was performed using FEM. Then, mean failure load of 6 anchors for each patient was compared between two groups. Moreover, an optimal cut-off value of the mean failure load was determined for predicting anchor failure. RESULTS: The mean failure load in the failed anchor group (70.3 N) was significantly lower than that in the stable anchor group (119.0 N; p<0.0001). In our method, the optimum cut-off value of the mean failure load was 75.4 N. CONCLUSIONS: Failure of the inserted TWINFIX™ anchor could be predicted using CT/3D-FEM. In this method, there seemed to be a high risk of anchor failure in shoulders with a mean failure load of <75.4 N.